Hot Rolling
Ensuring the maximum surface quality of the rolls throughout the entire rolling campaign and slowing down the increase of their roughness are the main goals of hot-rolling lubricant fluid to obtain strip or profile in the best possible condition. The process is also optimised by new formulations that prevent the appearance of residues in the nozzles.
Index
Hot-rolling oil
Product | Description |
TRENOIL SHD Series | Hot-rolling oils. High lubrication that increases the productivity of rolling processes and enables the rolling mill to achieve lower thicknesses at higher speeds. High adhesive properties that reduce work-roll wear and the number of mill stoppages for roll change. Very high lubricating power and good performance to ensure high strip quality. |
<Back
Fire-resistant hydraulic oils
Product | Description |
RENOSAFE HFDU (46,68) | Ester-based fire-resistant hydraulic fluid. Good lubricating properties. |
RENOSAFE FIREPROTECT 68 (HFDU) | Fire-resistant hydraulic fluid based on new ester and additive technology. High lubrication properties, high thermal and oxidation stability, high outgassing capacity, high viscosity index and shear stable. Multigrade characteristics, excellent compatibility with yellow metals, longer product life in service, increases the operating efficiency of the pump and hydraulic circuit, good characteristics against high scuffing loads. |
<Back
Flame-retardant hydraulic oils
Product | Description |
RENOSAFE HFC 500 (HFC) | Water/glycol type fire-resistant hydraulic fluid, formulated with rust-prevention additives and special additives against shear ageing. Anti-wear properties and protection against possible. |
<Back
Hydraulic systems
Product | Description |
RENOLIN B Series | High-performance demulsifying universal hydraulic and general lubrication oils (HLP). Good ageing resistance and with additives for better corrosion protection, excellent filterability, good viscosity-temperature behaviour, good wear protection, demulsifier (water-repellent), air release, contains zinc. Suitable for all hydraulic systems, even if thermal stress is present. The RENOLIN B range meets and exceeds the minimum requirements for HLP hydraulic oils according to DIN 51 524-2; ISO 6743 / 4, HM; ISO 6743 / 6, CKC; ISO 11158, HM; Denison HF0, HF1, HF2 |
RENOLIN HVI Series | Demulsifying hydraulic and general lubrication oils with a high viscosity index (HVLP). They are mineral oil-based and contain zinc and additives that improve ageing behaviour, corrosion and wear protection. RENOLIN B HVI oils are suitable for all hydraulic systems, especially if excess viscosity during start-up or insufficient viscosity at operating temperature is problematic. The high VI offers multigrade characteristics. Energy saving through high efficiency. These products are HVLP hydraulic and circulation oils according to DIN 51 524-3. Approvals: ISO 6743 / 4, HV. ISO 11158, HV. Denison HF0, HF1, HF2. |
RENOLIN MR Series | AW/EP hydraulic and circulation oils with high viscosity index (HVLPD). Detergents, dispersants, with exceptional cleaning properties and residue carrying capacity. Suitable for all hydraulic systems subject to wide temperature fluctuations or outdoor operations, e.g. sluices, reservoir machinery and machines or any application at especially low temperatures. HVLPD according to DIN 51 502 in conjunction with DIN 51 524. ISO 6743/4, HV. |
RENOLIN MR MC Series | Universal hydraulic and lubrication oils containing MC base oils with a high viscosity index. High-performance synthetic base (HVLPD), detergents, dispersants, with excellent oxidation and shear stability and exceptional cleaning and residue-carrying properties. Very wide operating temperature range. They allow oil change intervals to be extended. They have multigrade characteristics. Energy saving through high efficiency. They are HVLP oils according to DIN 51524-3. |
RENOLIN LD 10 | Fluid for cleaning hydraulic and lubrication circuits, free of chlorinated solvents, for cleaning and flushing hydraulic and lubrication circuits. Eliminates gumming caused by infiltrating cooling lubricants. Machines can continue to run normally during cleaning and flushing. However, an oil change is recommended because all contaminants are carried away. It is approved by DIN 51502: HLP, DIN 51524-2: HLP (except for demulsifying properties) and ISO 6743-4:HM. |
<Back
Greases and pastes
Medium/high temperature or load
Product | Description |
RENOLIT CX-EP 1 / RENOLIT CX-EP 2 | Calcium complex greases. Very high anti-wear and EP properties, total insolubility in water, good mechanical stability and corrosion protection. For very severe service conditions: high temperatures, heavy loads or very humid environments. |
RENOLIT LX EP 1 / RENOLIT LX-EP 2 | Lithium complex greases. For very severe service conditions: high temperatures, heavy loads or very humid environments. Very high anti-wear and EP properties, total insolubility in water, good mechanical stability and corrosion protection. |
RENOLIT H 443-HD 88 | Thermosetting, water-repellent and easily pumpable grease. For the lubrication of anti-friction bearings and plain bearings operating under high loads, at high temperatures and in humid atmospheres. Approvals: RWE Rheinbraun, FLENDER, SKF, SIEMENS. |
<Back
Very high temperature or load
Product | Description |
URETHYN MP 1 / URETHYN MP 2 | Polyurea-based grease. Resistant to high temperatures, high loads and highly resistant to environments with high humidity, even when in contact with salt water. For rolling and sliding bearings at high temperatures, e.g. long-term lubrication of bearings in electrical machines, fan bearings, rolling wheel bearings in continuous casting plants, pumping, blowing and compressor plants. Approvals: FLSmidth, Josef Fröhling, Loesche, Salzhausener Maschinenbautechnik SALMATEC, Sandvik, SMS Meer, ThyssenKrupp Resource Technologies, Zeppelin Baumaschinen, Amandus Kahl GmbH & Co. KG. |
URETHYN CC 2-1 | Polyurea-based grease. For rolling and sliding bearings subjected to high temperatures and humidity levels, e.g. roller bearings in continuous casting plants, as well as in the steel, raw materials and other industries. Approvals: German Steel Association VDEh according to SEB 181 255. |
URETHYN E/M 1 / URETHYN E/M 2 | Partly synthetic polyurea-based grease. High-temperature resistant. For lubrication of plastics, elastomers and sealing components as well as long-term lubrication of rolling and sliding bearings, e.g. in electric motor bearings in the textile industry, in blower bearings in dryers and ovens and spindles. Approvals: ANDRITZ, Bosch Rexroth, KHD Humboldt Wedag International, NEFF Gewindetriebe |
URETHYN E 2 | Fully synthetic polyurea-based grease. High-temperature resistant. For long-term or lifetime lubrication of rolling and sliding bearings in the chemical and textile industry, in conveying and drying systems, and in cataphoresis systems in the automotive industry. Approvals: Daimler, Eisenmann, EVG Lufttechnik, Sprimag Spritzmaschinenbau. |
RENOLIT HI -TEMP 100 / RENOLIT HI -TEMP 220 / RENOLIT HI -TEMP 460 | RENOLIT HI-TEMP 100 is a lubricating grease with a low coefficient of friction that improves efficiency at different torque speeds. Suitable for roller and ball bearings in electric motors, traction motors and brakes. Excellent corrosion and wear protection properties. RENOLIT HI-TEMP 220 and 460 are lubricating greases with a low coefficient of friction, but also with excellent anti-corrosion and wear protection properties even under adverse environmental conditions (humidity, harsh atmosphere, water). Especially recommended for the wet section of paper machines, but also for heavily-loaded bearings in any other industry and even in the automotive industry. |
RENOLIX CXI 2 / RENOLIT CXI 15 | Extremely stable grease, highly resistant to ageing. Suitable for lubrication points where good resistance to water and high loads is required. Developed to operate under severe conditions on rollers and rolling mills in steelworks, mines, quarries, cement works and construction machinery. |
RENOLIT CSX 15 | Grease resistant to ageing and high loads. Provides excellent corrosion protection even in the presence of salt water. Applicable and pumpable with centralised lubrication systems in a wide temperature range. Particularly suitable for plain and rolling bearings in steel rolling mills, in continuous casting processes and in the paper, mining and concrete industries. Approvals: TATA Steel. |
RENOLIT CX-HT 2 / RENOLIT CX-HT 0 | Fluid grease with black solid lubricants. Applicable by drip or spray system. Excellent protection against corrosion and weathering. For open gearing and gearwheels, plain bearings and rolling bearings generally subjected to high loads and low speeds. Especially recommended for cement plants, the ceramic industry, mining and other related industries. |
STABYL EHT 2 | Long-life high-temperature lubricating grease. For rolling and sliding bearings subjected to high thermal and mechanical loads. E.g. in drying plants, drive and conveyor systems, film stretching plants, etc. Approvals: Bernd Münstermann. |
<Back
Extreme temperatures
Product | Description |
RENOLIT SI 511 L | High-temperature silicone greases with polyurea thickener. For applications subject to high temperatures, e.g. wheel hubs of brick kiln wagons, hot air fans, material handling systems and door hinges of drying kilns and foundries, and control and regulating devices in vulcanisation shops. |
RENOLIT ST FTM-2 | Extreme temperature grease for roller and ball bearings. Not miscible with lubricants of a different nature. Recommended for flue gas. For all industrial applications: painting, calendering, stamping bearings, bearings for slow-running conveyor chains in textile equipment, in drying and annealing plants and in painting plants in the automotive industry and household appliance manufacturing. |
RENOLIT ST FTM 0-1 | Relubricating grease for extreme-temperature applications. Not miscible with lubricants of a different nature. Recommended for flue gas. For roller and ball bearings in all industrial applications: painting, calendering, stamping bearings, bearings for slow-running conveyor chains in textile equipment, in drying and annealing plants and in painting plants in the automotive industry and household appliance manufacturing. |
<Back
Greases and grease pastes with solid lubricants for high sliding or boundary friction conditions
Product | Description |
RENOLIT 62 MD | High-temperature grease containing MoS2. High anti-wear properties and good resistance to water and steam. Ideal for plain and rolling bearings at slow and medium speeds. Ovens, dryers, fans, extractors, etc. |
RENOLIT GL 10 | Semi-fluid EP grease with graphite as a solid lubricant. Highly adhesive, high water resistance and good corrosion protection. For lubrication of open gearing and cables. |
RENOLIT CX HT 2 / RENOLIT CX-HT 0 | Fluid grease with black solid lubricants. Applicable by drip or spray system. Excellent protection against corrosion and weathering. For open gearing and gearwheels, plain bearings and rolling bearings generally subjected to high loads and low speeds. Especially recommended for cement plants, the ceramic industry, mining and other related industries. |
CEPLATTYN 300 | Graphite paste with adhesion and high-pressure additives. Dry lubrication up to +500 °C. Priming lubricant for large open gears, racks and sliding surfaces. Also suitable for lubricating chains, sliding surfaces and adjustment gears in hydraulic steel constructions, in opencast and underground mining and for cable lubrication. It has the approvals mat. no. DB 106169, Ferry Capitain, FLSmidth, Gebr. Pfeiffer, KHD Humboldt Wedag International, Maschinenfabrik, Gustav Eirich, ThyssenKrupp Resource Technologies. |
GLEITMO WSP 5040 | High-performance white grease paste. Suitable for low sliding speeds and high loads as well as in case of contact rust. Application as a paste for threaded joints subjected to high temperatures up to +1200 °C. Suitable for machine components of all kinds that are subject to very high pressures, heavy loads and oscillating movements. Particularly in wet environments or under the effects of splashing water. For sliding surfaces that are prone to stick-slip and seizure. It is approved by COLUMBUS McKINNON Engineered Products (Pfaff-silberblau), NEUERO Industrietechnik für Förderanlagen, Sandvik, ThyssenKrupp Steel Europe. |
<Back
Lubricating and assembly pastes for applications with very high loads or temperatures
Product | Description |
MEISSELPASTE | Copper-coloured lubricating paste. Range -20 to 1100 ºC. Dry lubricant film up to 1100°C for the lubrication of nestable tools, e.g. wear bushings in hydraulic and pneumatic hammers (ref: KRUPP, MONTABERT, RAMMER, INDECO, and others) from 75 to 6000 kg in weight, compressed-air drills and other equipment. Also for underwater and hot applications. Approvals: BAIER & KÖPPEL, DELIMON, LINCOLN. |
GLEITMO 100 | Assembly pastes with a wide range of applications. From approx. +140 °C purely dry lubrication due to solid lubricants. Facilitates assembly and disassembly and prevents stick-slip. For the running-in lubrication of heavily-loaded sliding bearings, slide and guide rails, gearwheels and threaded spindles as well as for the lubrication of bolts and bolted joints. Approvals: Daimler, Josef Fröhling, KHD Humboldt Wedag International, CAF. |
GLEITMO 705 / GLEITMO 705-0 | Lubricating paste. Maintains its lubricating and separating properties at very high temperatures, increases the operational safety and service life of hot systems and tools. Suitable for slow-running bearings, pins, hinges, joints and slide rails in combustion, drying and annealing plants. Use as graphite lubricant for casting ladles. Gleitmo 705 is ideal for initial lubrication, while Gleitmo 705-0 is ideal for relubrication operations using centralised lubrication systems. |
GLEITMO WSP 5040 | High-performance white grease paste. Suitable for low sliding speeds and high loads as well as in case of contact rust. Application as a paste for threaded joints subjected to high temperatures up to +1200 °C. Suitable for machine components of all kinds that are subject to very high pressures, heavy loads and oscillating movements. Particularly in wet environments or under the effects of splashing water. For sliding surfaces that are prone to stick-slip and seizure. It is approved by COLUMBUS McKINNON Engineered Products (Pfaff-silberblau), NEUERO Industrietechnik für Förderanlagen, Sandvik, ThyssenKrupp Steel Europe. |
<Back
